191–200 of 281 posts
Earlier quoted context omitted.
have you used this one? I'd like to buy it, I'd just want to hear that someone used this successfully.
Yes, my son built is a few weeks ago, no issues and works great!
> just be careful not to overspend on your first iron. I first learned how to solder on an ultra-cheap hardware-store unit, and you should, too I beg to differ. I used to suck at soldering, and while I'm still no expert, swapping my €20 basic soldering iron for a serious Weller unit (starting at €150) changed everything. The Weller heats up almost instantly, goes up as high as you want, and stays at a constant temper…
Its the rule supposedly came up with by Adam Savage - buy cheap tools, use em til you break em, then replace the ones you break with expensive, good tools. The idea of that rule is so new makers can work out what tools they actually are using, so they don't waste a shitload of money. In practice? Some tools are just worth spending the money on upfront, inferior tools will often lead to frustration and failure early o…
Using lead solder is kind of retro. There are good lead-free solders now. If you get the kind with 3% silver, you pay $5 instead of $3 for a small spool, but it's much easier to get good results. Also, that stuff is no-clean, which simplifies things.
If I may, I would complete a few points in the article. Soldering iron: Get a decent one. That doesn't mean you must throw a boatload of money, just avoid the crappy ones, which almost always are the cheaper ones. A notable exception is the Pinecil by Pine64.org, which is truly a great iron despite being cheap. Pinecil aside, you can snatch a used Weller or Hakko on ebay without spending too much, but beware of the m…
> A notable exception is the Pinecil by Pine64.org, which is truly a great iron despite being cheap. I have a Pinecil and I like it, but I feel that it's not a good recommendation for a first soldering iron. The UI may be confusing for some, it doesn't come with a power supply, the tips are fairly expensive, and there's no place to rest the iron while using it. Instead, I would tell a newbie to get a middle-of-the-ro…
> just be careful not to overspend on your first iron. I first learned how to solder on an ultra-cheap hardware-store unit, and you should, too I beg to differ. I used to suck at soldering, and while I'm still no expert, swapping my €20 basic soldering iron for a serious Weller unit (starting at €150) changed everything. The Weller heats up almost instantly, goes up as high as you want, and stays at a constant temper…
Its the rule supposedly came up with by Adam Savage - buy cheap tools, use em til you break em, then replace the ones you break with expensive, good tools. The idea of that rule is so new makers can work out what tools they actually are using, so they don't waste a shitload of money. In practice? Some tools are just worth spending the money on upfront, inferior tools will often lead to frustration and failure early o…
no, you can't undermine the idea with this trick. For example (grabbing examples from other comments in this thread), while an expensive soldering iron might be much better than a cheap one, there is no way you know before you start whether you're going to be soldering a lot.
I know how to solder, I've soldered a lot since I was about 13, and I can solder just fine with a crappy soldering iron (just like good pizza makers can use a primitive wood fired oven) but after I learned to wire-wrap, I put down my soldering iron almost for good... and does wire-wrapping even exist any more? If I wanted to take it up again, I'd find antique wirewrapping tools before I'd torture myself with soldering anything. All of which is my way to say, if I can't predict how much soldering I'm going to do, then no beginner can predict whether an expensive soldering iron is what they need or not.
Maybe if you went out and geared up with the most expensive technical mountain climbing gear, you could climb Everest on your first try, and you could then make the case that had you bought the cheap stuff you would have been discouraged by frostbite. But that's just not a good plan.
> As you’re applying heat with your soldering iron, it’s important to have the metal tip heating both the pad and the solder that’s going onto it—note the location where I’m placing the iron.
But there's no picture to "note the location where I'm placing the iron" in? Was this article written somewhere else and repurposed and they missed a picture?
Thank you, this is great! On another note, what to solder ? I've been playing around with arduinos and esp 32s but so far I've just used breadboards and didn't have to solder. Any recommendations for an easy project to take on?
Earlier quoted context omitted.
Assuming you place no value on your own time & frustration…
FWIW, I learned this approach while working in the trades as a welder. You have consumables in stock and ready to go, and that includes extra grinders. Some tools you do take the time and effort to really take care of, of course, but a lot more than you might think are in the cattle not pet category of things.
Earlier quoted context omitted.
Assuming you place no value on your own time & frustration…
FWIW, I learned this approach while working in the trades as a welder. You have consumables in stock and ready to go, and that includes extra grinders. Some tools you do take the time and effort to really take care of, of course, but a lot more than you might think are in the cattle not pet category of things.
But I've bought two grinders and have an ancient cheap one from father in-law. My cheap Metabo is relatively quiet and smooth. Cheap Lidl one is loud and jerky. Ancient one I've just thrown away at how bad it was to use. Recently I had to grind some tubing for > hour and my wrists felt it even with the Metabo entry level. Supposedly the pro versions have antivibration, better balanced, speed control, etc.
My point being if I was using this 5 days a week for >1h I'd invest in ease of use/comfort/safety - no ? I'd probably have a few throwaway ones for backup.
> just be careful not to overspend on your first iron. I first learned how to solder on an ultra-cheap hardware-store unit, and you should, too I beg to differ. I used to suck at soldering, and while I'm still no expert, swapping my €20 basic soldering iron for a serious Weller unit (starting at €150) changed everything. The Weller heats up almost instantly, goes up as high as you want, and stays at a constant temper…
I cry for all the time I wasted soldering before finally sucking it up and getting a Metcal.