> just be careful not to overspend on your first iron. I first learned how to solder on an ultra-cheap hardware-store unit, and you should, too I beg to differ. I used to suck at soldering, and while I'm still no expert, swapping my €20 basic soldering iron for a serious Weller unit (starting at €150) changed everything. The Weller heats up almost instantly, goes up as high as you want, and stays at a constant temper…
How To Get Started In Soldering
61–70 of 281 posts
Re: How To Get Started In Soldering
#62> Much like the ability to drive a car with a manual transmission, read a map, or write a check, Gen Z is learning less and less about how to work with their hands—and it’s time for that to change. Ugh. Let's talk down the youngest generation of adults to justify a basic tutorial article. Ironically no one of Gen Z, that I know of, is unable to do any of those examples.
Re: How To Get Started In Soldering
#63> just be careful not to overspend on your first iron. I first learned how to solder on an ultra-cheap hardware-store unit, and you should, too I beg to differ. I used to suck at soldering, and while I'm still no expert, swapping my €20 basic soldering iron for a serious Weller unit (starting at €150) changed everything. The Weller heats up almost instantly, goes up as high as you want, and stays at a constant temper…
Re: How To Get Started In Soldering
#64> Much like the ability to drive a car with a manual transmission, read a map, or write a check, Gen Z is learning less and less about how to work with their hands—and it’s time for that to change. Ugh. Let's talk down the youngest generation of adults to justify a basic tutorial article. Ironically no one of Gen Z, that I know of, is unable to do any of those examples.
While I can see why you might take that as "talking down the youngest generation of adults", I don't think that is necessarily the author's intention. All three of those examples are things that many people from Gen Z often don't ever do. They are also all still valuable skills that I believe are still worth knowing. I agree that it is bad to talk down to people just because they are young. It is also bad to dismiss…
As I get your post based on the amount spent on why it’s bad to dismiss older persons, I don’t think this is really what the article or GP suggested. similarly, I am not sure that it’s fair to say genz often doesn’t do a lot of the mentioned things. GenZ is full of individuals specializing in niche or old fashioned skills and showing the skills off on specific mediums. Coding and repair twitch streams are quite common, just maybe not as much as subjects that are easier to appreciate without much knowledge in the subject. It’s pretty easy for most people to grasp why a contortionist’s skill or someone skilled with sewing has a rare and unique talent. it’s a lot easier to understand what went into it and the precision and the result is very apparent. I think it’s not so clear with subjects like electronics repair as the tech might work afterwards, but there is too much to understand going into it to fully appreciate the result in its own, and thus audiences rely on the presenter to fill the gaps.
The authors examples are good ones if you’re already inclined towards fixing stuff on your own; but if it were me, even with a simple fix like string lights, i’d have a hard time justifying repairs on my own as i’d need to invest into the repair kit and it would be hard to shake concerns on if I did a safe repair or if I made a mistake that needs to be fixed. I imagine it’s like this for many, as even a few years back when I did laptop repair at a university, students (even technical ones) were antsy about such manual repairs and fixes, and often just preferred to put the liability on someone else. for something really disposable like lights, a cheap phone, etc, i can easily get why people of all ages would just prefer a new one.
Soldering is a fun hobby, and i think that the hobbyist community would easily eat it up if they don’t already (i’m positive you can find some electronics repair vids/channels). it is just lacking practical reasons for people to be interested and/or personalities to bring people to it.
Re: How To Get Started In Soldering
#65Being self-reliant for stuff like that is basic productivity stuff.
Re: How To Get Started In Soldering
#66Re: How To Get Started In Soldering
#67> Much like the ability to drive a car with a manual transmission, read a map, or write a check, Gen Z is learning less and less about how to work with their hands—and it’s time for that to change. Ugh. Let's talk down the youngest generation of adults to justify a basic tutorial article. Ironically no one of Gen Z, that I know of, is unable to do any of those examples.
Re: How To Get Started In Soldering
#68Aaah, this is really not a good beginner's guide to soldering! Cranking up to max temperature might work a lot of the time but runs the risk of frying ICs and causing PCB traces to come off. Also using a wet sponge can cause the tips to rust. It's much better to clean them with a brass "sponge" leaving the tip tinned to protect it. Finally the real key to easy soldering is solder flux (and leaded solder if you're all…
A wet sponge doesn't cause rust, it's occasionally blamed for cracking plating when you use a high temperature. If you use a moderate temperature (650°F/340°C) it's a gentler way to clean flux residue off the tip. Brass wool I reserve for scrubbing oxidation off the tip, but this eventually wears through the plating so I don't do this often. Leaded solder is both toxic and completely unnecessary for hobbyist use. I l…
My budget is more in the $20 - $25 range. Cheap adjustable-temp soldering irons are available for under $4 [0], surely there is some middle ground between those irons and the $115 unit you suggest?
Re: How To Get Started In Soldering
#69> just be careful not to overspend on your first iron. I first learned how to solder on an ultra-cheap hardware-store unit, and you should, too I beg to differ. I used to suck at soldering, and while I'm still no expert, swapping my €20 basic soldering iron for a serious Weller unit (starting at €150) changed everything. The Weller heats up almost instantly, goes up as high as you want, and stays at a constant temper…
Electronics are heat sensitive. A reliable solder joint needs to heat quickly, flux stripping off any oxidized layers, everything melted, before the heat goes up the lead and fries the component.
This means you want an iron that is temperature controlled, and heavy enough it has some thermal mass so it doesn't cool quickly.
I've worked with cheap irons after getting used to my $60 temperature controlled iron, and yes you can use them, but it requires more experience, skill and care to do well, which in practice is equivalent to saying less reliable results.
Re: How To Get Started In Soldering
#70> Much like the ability to drive a car with a manual transmission, read a map, or write a check, Gen Z is learning less and less about how to work with their hands—and it’s time for that to change. Ugh. Let's talk down the youngest generation of adults to justify a basic tutorial article. Ironically no one of Gen Z, that I know of, is unable to do any of those examples.
it goes both ways. most of the gen z folks i know can't read a clock or focus on a movie