A dozen USB chargers in the lab: Apple is very good, but not quite the best

Ai Charger, specifically:

http://event.asus.com/mb/2010/ai_charger/

http://asus-ai-charger.en.uptodown.com/

I had to uninstall it, when I upgraded from Windows 7 to 8, though.

I dunno, I mix iPhone, iPad, Kindle, Samsung (Nexus) and Griffin chargers all the time, bring only one of them (typically iPad) on the trips, and it works out completely fine. I think that Kindle and Griffin are the slowest though.

This one is also nice

http://www.ubergizmo.com/2009/07/cambrionix-49-port-usb-hub/

For the general case, all other parameters being equal (supply mode, quality and so on): bigger charger -> larger dead load.

An iPad charger is not a 'large' charger, it's a fairly small step up from an iPhone charger, since you are reporting 3.0 watts of 'wall power' but your multiplication of scope measured values does not correct for power factor you are likely off by quite a bit on both measurements.

GP mentioned a HP touchpad charger to charge a phone, I don't have a HP touch pad charger here but the specs are quite terrible [1], you'd have to measure with that specific charger to answer the specific question or you'd have to do a comparison of a large range of chargers with accurate measurement methodology in order to really answer the general question.

As it is your conclusion contradicts practical engineering and I'm afraid it will not hold up in a better test, which would be to try a number of switched mode supplies of various sizes designs with various loads. Plugging in one device and doing a hasty (wrong, ignoring phase shift) measurement does not warrant your conclusion.

To measure efficiency you're going to have to take the power factor[2] into account, this can be quite hard to do, and theoretical efficiency doesn't matter for a practical test (you're measuring, not theorizing).

The wave forms that switched mode chargers [3] output and consequently the kind of load they represent to the grid is so irregular that most non-caloric and power factor corrected measurements will give values that are not accurate. That noise that is present on the output wires will be to some extent visible on the input side.

A normal Watt meter will work best with transformer based supplies or resistive loads, accuracy for small switched mode loads will be anywhere from 'so so' to 'terrible' depending on the make and model power meter. Good brands (for instance Fluke) do most calculations right and will be able to deal with CFLs and other phase shifted loads, bad brands (I won't name them but they're killing it in the domestic watt meter department) will give wildly in-accurate results.

But even a quality meter like a Fluke will still have trouble with this kind of spiky load, especially if it is small.

It would probably be a good idea to (properly) describe your test rig along with the results it says:

"I measured the AC input voltage and current with an oscilloscope. The oscilloscope's math functions multiplied the voltage and current at each instant to compute the instantaneous power, and then computed the average power over time. For safety and to avoid vaporizing the oscilloscope I used an isolation transformer. My measurements are fairly close to Apple's[15], which is reassuring. "

But you can't really do it that way and get accurate results, instantaneous power draw using a switching supply changes several hundred thousand times per second and is likely phase-shifted so a simple multiplication is not going to work.

Accurately measuring (low) power draw from switched mode consumers is a really tricky problem, it's easy enough to read some numbers from a display but I can assure you that this is not a simple problem to work on if you want to get meaningful results.

[1] http://en.wikipedia.org/wiki/HP_TouchPad#Power_adapter

[2] http://en.wikipedia.org/wiki/Power_factor

[3] http://en.wikipedia.org/wiki/Switched-mode_power_supply

Thank you for your detailed comment. I went to a great deal of effort in my article to measure the power consumption accurately, accounting for the power factor, but I left out most of the details since most people don't care. I'm not multiplying the average current and average voltage to compute watts, because that obviously would not work due to the power factor. Instead, I'm multiplying the instantaneous voltage and current 50,000 times a second and summing this up, which gives the actual power, corrected for the power factor. (While the internal current changes tens of thousands of times a second, the line current changes slowly due to the input filtering, so this is plenty of resolution. I'm using a Tektronix TDS5104B 1 GHz oscilloscope, so I have a pretty accurate view of the input voltage and current.)

The main sources of error in my measurements are the cheap isolation transformer (which causes a bit of line voltage distortion under load), the current sense resistor, the tolerances of the voltage divider resistors, and noise in the measurements. So I wouldn't claim these measurements to be better than 10%.

You can take a look at one of the oscilloscope power graphs at https://picasaweb.google.com/lh/photo/pbrO8BQz38kDo9xU5ejffd... Yellow is the input voltage, and turquoise is the input current. The non-sinusoidal current shows the non-unity power factor. Note that there's no phase shift, but instead the current flow happens only at the voltage peaks (which is a consequence of the input diode bridge, not of the switching power supply per se.) At the bottom of the image is the instantaneous power, computed from the instantaneous voltage and current.

For the iPad vs iPod measurement above, I didn't have the oscilloscope handy so I used a Kill-A-Watt, which does in fact take the power factor into account.

Going back to your statement that "bigger charger -> larger dead load". By "dead load", do you mean the power consumption under no load, which I call "vampire power" in the article? This varies widely between chargers, having more to do with the design than the size of the charger. But in any case, this wasted power is pretty much irrelevant under load. For instance, 100 mW is a typical vampire power usage. So if a hypothetical larger charger has twice that wasted power, at a 3 watt load, this is only a 3% difference.